Raspberry Pi Display 2.13inch E-Paper / E-Ink Module (B) for Raspberry Pi Pico, 212 x 104, Red / Black / White, SPI [19588]

Raspberry Pi Display 2.13inch E-Paper / E-Ink Module (B) for Raspberry Pi Pico, 212 x 104, Red / Black / White, SPI [19588]

Be the first to review this product

Hurry! 2 items left!

Price	$43.93
	Collect 129 Everyday Rewards points Score 3x points on every order Ends 11:59pm 03/12/2024. Exclusions & T&Cs apply Log in to MyDeal to link your card
Shipping	Unable to calculate delivery for , please Contact Us Delivery unavailable to Change
	See delivery details

Quantity

Add to wishlist

Raspberry Pi Display 2.13inch E-Paper / E-Ink Module (B) for Raspberry Pi Pico, 212 x 104, Red / Black / White, SPI

NOTE: Raspberry Pi Pico is NOT included. The pictures are for reference ONLY.
2.13inch E-Paper E-Ink Display Module (B) For Raspberry Pi Pico, 212×104 Pixels, Red / Black / White, SPI Interface

SPI Timing:

Note: Different from the traditional SPI protocol, the data line from the slave to the master is hidden since the device only has a display requirement.
- CS is slave chip select, when CS is low, the chip is enabled.
- DC is data/command control pin, when DC = 0, write command, when DC = 1, write data.
- SCLK is the SPI communication clock.
- SDIN is the data line from the master to the slave in SPI communication.
SPI communication has data transfer timing, which is combined by CPHA and CPOL.
1. CPOL determines the level of the serial synchronous clock at an idle state. When CPOL = 0, the level is Low. However, CPOL has little effect on the transmission.
2. CPHA determines whether data is collected at the first clock edge or at the second clock edge of the serial synchronous clock; when CPHL = 0, data is collected at the first clock edge.
- There are 4 SPI communication modes. SPI0 is commonly used, in which CPHL = 0, CPOL = 0.
As you can see from the figure above, data transmission starts at the first falling edge of SCLK, and 8 bits of data are transferred in one clock cycle. Here, SPI0 is in used, and data is transferred by bits, MSB first.
Working Protocol
This product is an E-paper device adopting the image display technology of Microencapsulated Electrophoretic Display, MED. The initial approach is to create tiny spheres, in which the charged color pigments are suspending in the transparent oil and would move depending on the electronic charge. The E-paper screen display patterns by reflecting the ambient light, so it has no background light requirement.
(Note that the e-Paper cannot support updating directly under sunlight).
How to define pixels
In a monochrome picture we define the pixels, 0 is black and 1 is white.

- The dot in the figure is called a pixel. As we know, 1 and 0 are used to define the color, therefore we can use one bit to define the color of one pixel, and 1 byte = 8pixels
- For example, If we set the first 8 pixels to black and the last 8 pixels to white, we show it by codes, they will be 16 bit as below:

For computer, the data is saved in MSB format:

So we can use two bytes for 16 pixels.
For 2.13inch e-paper B, the display colors are red, black, and white. We need to split the picture into 2 pictures, one is the black and white picture, another is the red and white picture. When transmitting, because one register controls a black or white pixel, one controls Red or white display. The black and white part of 2.13 use 1 byte to control 8 pixels, and the red and white part use 1 byte to control 8 pixels.
For example, suppose there are 8 pixels, the first 4 are red, and the back 4 are black:
They need to be disassembled into a black and white picture and a red and white picture. Both pictures have 8 pixels, but the first four pixels of the black and white picture are white, the last 4 pixels are black, and the first 4 pixels of the red and white picture One pixel is red, and the last four pixels are white.

If you define that the data of white pixel is 1 and the black is 0, then we can get:

So that we can use 1 byte to control every eight pixels.

User Guides, Resoures, please check HERE

OPERATING VOLTAGE
3.3V

INTERFACE
3-wire SPI, 4-wire SPI

OUTLINE DIMENSIONS
65.00 × 30.50mm

DISPLAY SIZE
48.55 × 23.71mm

DOT PITCH
0.229 × 0.228mm

RESOLUTION
212×104 pixels

DISPLAY COLOR
red, black, white

GREY SCALE
2

FULL REFRESH TIME
15s

REFRESH POWER
26.4mW (typ.)

STANDBY CURRENT
<0.01uA (almost none)

VIEWING ANGLE
>170°
- MPN: 19588

MPN: 19588

Shipping Details

Final Delivery by Aus Post

Changing your mind / purchasing the wrong product by mistake

If you change your mind after making a purchase, or realise you have purchased the incorrect item, you can enjoy the peace of mind that we offer a 7 day exchange policy. (excludes special order items).

If there is not a suitable product that can be exchanged for your returned item you will be offered a refund to your account based on the value paid at the time of purchase.

to supply the correct product the incorrect product will first need to be returned to us;
we will need to be notified within 7 days of purchase / delivery;
the incorrect product supplied must be in a sealed / unopened condition.

Incorrectly supplied products

If you have been accidentally supplied the wrong product, F Digital can supply the correct product (where it is available) or issue a refund.

In order to supply the correct product, the incorrect product will first need to be returned to us. F Digital can arrange a return ticket to send the incorrect product back by courier.

In this scenario we will need to be notified ASAP and the incorrect product supplied must be in resalable / unused condition with original packaging and accessories.

Products damaged in transit

If your product has been damaged during transit to your delivery address an investigation will be conducted. Once the investigation has reached a conclusion and it is determined the product has been damaged in transit we will offer a refund.

Please contact us ASAP. We will then advise you to visit your nearest Australia Post Office so that they can investigate the damage. You will need to keep all packaging so that their team are able to make a fair assessment.

Products that are faulty within the warranty period

If your product is faulty or has stopped working as intended and is still within the warranty period specified when you purchased your product, F Digital will repair or or issue a refund.

In order to repair or issue a refund for your faulty product, it will need to be returned to us so we can test and confirm that it is faulty. For some products you may also be able to contact the manufacturer directly to arrange a repair / replacement.

Returns of this nature can be made any time within the warranty period and it is your responsibility to cover any costs of returning the product to us.

Testing fees and return freight

If you return a product to us that is not faulty, you may be liable for a testing fee and freight charges to return the product to you.

Returns may take approximately 4 weeks to arrive back with our returns team in NZ to process.

Restocking fees

In some special circumstances, we may agree (at our discretion) to accept a return of a product that is not faulty. In these situations there will be a handling fee equal to at least 20% of the purchased price. Delivery, service and assembly fees are not refunded at all.