| PEAK DATA SPEED (MODEL DEPENDENT) | - LTE FDD: Max 10 Mbps (DL) / Max 5 Mbps (UL)
- LTE TDD: Max 8.96 Mbps (DL) / Max 3.1 Mbps (UL)
- DC-HSPA+: Max 42 Mbps (DL) / Max 5.76 Mbps (UL)
- UMTS: Max 384Kbps (DL) / Max 384Kbps (UL)
- EDGE: Max 236.8 Kbps (DL) / Max 236.8 Kbps (UL)
- GPRS: Max 85.6 Kbps (DL) / Max 85.6 Kbps (UL
|
| ANTENNA CONNECTORS | - 2 x SMA connectors for 4G/3G/2G (1 x Main and 1 x RX Diversity)
- 1 x SMA connector for GPS
|
| INTERFACES | - 1 x 100Base-T Ethernet RJ45 port
- 1 x RS232 Serial Port DB-9 female DCE supporting either 9 wire RS232 or RS485/RS422 (software selectable)
- Software controlled termination resistors for RS485
- 1 x Micro USB 2.0 OTG interface with 0.5A supply capability
- I/O terminal block providing:
- – 3 x Multipurpose I/O pins
- – NAMUR (EN 60947-5-6 / IEC 60947-5-6) compatible sensor input
- – Analogue 0V to 30V input
- – Digital input (through measurement of voltage above/ below threshold)
- – Open collector output
- 1 x Recessed multifunctional reset button
- – Reboot
- – Reboot into recovery mode
- – Reset to factory default settings
|
| LED INDICATORS | - 8 x tri-colour LEDs
- – Power, Network, a GPS/customizable LED and 5x
- Signal Strength indicators
- Easy and clear LED status display for connection status, connected network type, and connection errorsGP
|
| GPS | - GPS
- GLONASS
- BeiDou
- Galileo
- QZSS
|
| SIM CARD READER | - 1 x SIM card slot
- – Supports Mini USIM/SIM Format (2FF)
- – Optional soldered-down SIM (ETSI MFF2 DFN-8 USIM)
|
| PROCESSOR AND STORAGE | - – 800 MHz ARM Cortex A8 processor with 128 MB RAM
- – 512 MB flash memory storage
- Advanced Diagnostics and Control via SMS
- – Query status information – such as Signal Strength, WAN IP, Uptime, and many more
- – Configure device remotely via SMS – such as APN, authentication settings, and many more
- Execute commands via SMS – such as reboot, reset to defaults, go offline, and many more
- Secure SMS management using sender whitelisting and password management
|
| FIRMWARE MANAGEMENT | - Firmware Upgrade locally via LAN or remotely Over-TheAir (HTTPS, SNMP, TR-069, LWM2M)
- Multiple firmware image storage on device and dynamic install
- Triggered firmware upgrade via SMS (initiate download & install from HTTPS)
|
| SOFTWARE DEVELOPMENT KIT | - Develop and install custom software applications
- Open Linux standard development environment
- Develop applications/scripting in standard ANSI C/Shell script and LUA
- Package manager built into Web-UI for Application installation/removal
|
| CELLULAR | - Profile managed packet data connections
- NAT Disable for framed route configuration
- Transparent bridge mode using PPPoE to allow the router to transparently forward Public WAN IP address to a downstream device
- SIM Security Management (PIN configuration, enable and disable)
- Automatic and manual cellular band selection
- Automatic and manual operator selection
- Odometer reading available via Web-UI, CLI and SDK
|
| NETWORK & ROUTING | - Static Routing, RIP (v1/v2), Port Forwarding and DMZ
- Dynamic DNS
- VRRP for redundant router failover
- – DHCP Server including address reservation by MAC address
- – Custom DNS server definitions
- – DHCP Relay
- – DHCP list display in Web-UI
- – Advanced DHCP Option configuration (Option 42 NTP, Option 66 TFTP, Option 150, Option 160)
- Data Stream Manager providing ability to create mappings between input and output ports (e.g. Serial
- Port, SMS, USB) and perform required translation or data processing by each virtual tunnel.
- Modbus Server TCP/IP Gateway and Client TCP/IP Agent with up to 247 slaves connected to the Serial TCP/IP Gateway.
- Modbus RTU/ASCII frames support
|
| VPN | - PPTP Client for VPN connectivity to remote PPTP VPN Server
- IPSec tunnel termination (for up to 5 tunnels)
- GRE Tunnelling
- OpenVPN (Client, Server and P2P)
|
| ADMINISTRATION & CONFIGURATION | - Secure web-based user interface (HTTPS) for full device status and configuration
- Password protected configuration file backup and restore for quick device configuration and device cloning
- SSH Command Line Interface for status monitoring, configuration and control
- SNMP v1/v2/v3 including cellular specific MIB, config and firmware download
- TR-069 Client for remote device configuration, configuration backup and restore, and firmware upgrade
- SMS Client (Send/Receive) including inbox, outbox
- Ping monitor watchdog (Reset connection on repeated ping failure)
- Diagnostic Log Viewer (remote and local)
- System Status and Security Logs
- NTP Server Support for network time sync of device’s system clock
- Device User Guide stored on the device and accessible via the secure web-based user interface (HTTPS)
- API (C, LUA and Shell libraries) to the unit’s internal Runtime Database to allow full status monitoring configuration and control of the device from custom applications
|
| TEMPERATURE | - Operating Temperature Range: -40°C to +70°C
- Storage Temperature Range: -40°C to +85°C
- Operating Humidity Range: 0-95%
|
| POWER SUPPLY | - Power input via 6-way termination block receptacle
- Field terminable power input via screw type terminal block included
- DC Power (8 - 40V DC)
- 1 x Dedicated ignition input and 3 x I/O ports on 6-way connector (only available on some models)
- Power consumption 6W, recommended DC supply via terminal block (12V 1.5A)
- Vehicle compatible protection on DC Input Jack. (ISO7637 standard)
|
| DIMENSIONS, WEIGHT & MOUNTING | - Device dimensions (excluding external antenna): 143 mm
- (L) x 107 mm (W) x 34 mm (D) / 221 g (254 g with bracket)
- Wall mount support in multiple orientations via embedded mounting holes
- DIN Rail mount support via plastic bracket included in box (Top hat section rail TH 35 IEC60715)
|
10% Coupon
